Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 04:13 12 Nov 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 367623 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 536515   02:49pm 16 Dec 2015
Normal Topics  

   Page 74 of 99    

Pipe size imsmooth, 03/06/2008 2 4757   12:14pm 03 Jun 2008
F&P goodies dazz, 30/05/2008 11 7573   10:42am 01 Jun 2008
Single Dual Stator windmill dazz, 26/05/2008 19 6164   11:41am 31 May 2008
Cable connection to stator imsmooth, 29/05/2008 8 3726   10:46am 31 May 2008
Newbie in need of suggestions... rustybucket, 24/05/2008 7 5189   11:43am 30 May 2008
Optimum TSR dazz, 28/05/2008 6 4572   05:08am 30 May 2008
My Washingmachine broke - YaY! King Edward, 30/05/2008 3 4064   11:11pm 29 May 2008
13ft problem aussiekiwi, 22/05/2008 12 4706   04:18am 29 May 2008
Get-together nice_pak2002, 28/05/2008 1 3863   09:00pm 28 May 2008
first time post wandyhee, 27/05/2008 4 4012   03:29am 28 May 2008
Angle of attack CB365, 27/05/2008 2 3797   11:39pm 27 May 2008
Completely new... no idea where to start computerguy, 26/05/2008 4 5110   11:32pm 25 May 2008
Blowing in Brisbane - 3.796 KWh fillm, 18/05/2008 5 6084   11:57am 25 May 2008
7 phase F&P using hard drive magnets spiral, 06/05/2008 34 18632   10:48am 25 May 2008
Beginning nice_pak2002, 23/05/2008 4 3821   10:43am 25 May 2008
dismantling chinese windmill.. Steve9R, 25/05/2008 1 3584   09:35am 25 May 2008
formula question dazz, 25/05/2008 2 3492   01:25am 25 May 2008
SMFIS dazz, 21/05/2008 14 4340   03:52pm 24 May 2008
I-beam tower? imsmooth, 24/05/2008 2 3880   07:09am 24 May 2008
Blade design 311fan, 21/05/2008 11 5242   01:52pm 22 May 2008
Mounting the Bearings for Randy’s Weldmen imsmooth, 19/05/2008 0 3459   10:14pm 18 May 2008
25 rotor turbine azland00123, 16/05/2008 5 3555   07:19pm 17 May 2008
Testing the neo rotor imsmooth, 14/05/2008 6 5342   06:49am 15 May 2008
F&P Newbie RevUpWind, 03/05/2008 3 4135   11:43pm 14 May 2008
Use a ventilator/Savonius? jlsawell, 13/05/2008 2 4971   02:56am 13 May 2008
= New posts since you last visited .      

   Page 74 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026