Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 06:04 12 Nov 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 367630 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 536521   02:49pm 16 Dec 2015
Normal Topics  

   Page 63 of 99    

3 Phase DaViD, 14/02/2009 2 2980   07:42am 15 Feb 2009
How much output can I expect heynow999, 15/02/2009 1 3182   07:36am 15 Feb 2009
F&P DaViD, 13/02/2009 1 2986   08:07pm 12 Feb 2009
Working load of steel cable imsmooth, 11/02/2009 3 3248   01:31pm 11 Feb 2009
resistance DaViD, 10/02/2009 2 2982   01:00pm 11 Feb 2009
lightning protection imsmooth, 09/02/2009 6 4122   02:32pm 10 Feb 2009
FIRE DaViD, 10/02/2009 0 2912   05:42pm 09 Feb 2009
avarage voltage DaViD, 07/02/2009 2 3495   05:29pm 09 Feb 2009
New Windmills & Mixing batteries RevUpWind, 06/02/2009 15 5576   12:02am 09 Feb 2009
wind wave turbine faroun, 02/02/2009 20 6963   12:15am 08 Feb 2009
car starter motor used as generator? iguana9999, 07/02/2009 6 13932   02:49am 07 Feb 2009
7.5HP Three Phase Motor Conversion SparWeb, 24/09/2008 54 33356   08:50pm 06 Feb 2009
miniture DaViD, 05/02/2009 4 3650   03:39pm 06 Feb 2009
no juice... birdhouse, 05/02/2009 5 3423   03:53pm 05 Feb 2009
motor DaViD, 06/02/2009 0 3091   03:08pm 05 Feb 2009
Neo conversion brucedownunder2, 03/02/2008 51 15758   02:52am 05 Feb 2009
Wiring for Savonius? Mr.Sleepy, 29/01/2009 13 5437   08:39pm 03 Feb 2009
Simple and accurate RPM measurement imsmooth, 31/01/2009 4 3984   06:37am 03 Feb 2009
10.5’ cedar/epoxy blades flying imsmooth, 02/02/2009 1 3787   05:10am 03 Feb 2009
Fisher & Paykel model preference catchnthe-)))), 01/02/2009 0 3199   03:56am 01 Feb 2009
Windmill System crazyk, 29/01/2009 16 4885   08:48am 31 Jan 2009
another newbie question birdhouse, 29/01/2009 15 4882   11:30pm 30 Jan 2009
blade weight comparing catchnthe-)))), 21/01/2009 6 3457   12:23pm 30 Jan 2009
Motor crazyk, 28/01/2009 6 3890   01:10am 30 Jan 2009
motion conversin question! faroun, 29/01/2009 6 3143   01:01am 30 Jan 2009
= New posts since you last visited .      

   Page 63 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026