 Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me. |
Forum Index : Microcontroller and PC projects : RP2350 HDMI with 720P goodness
  Page 4 of 4 |
|||||
| Author | Message | ||||
Sasquatch Guru  Joined: 08/05/2020 Location: United StatesPosts: 362 |
Ok, this IC seems to fit the bill for a single ended to differential HDMI line driver: https://www.ti.com/lit/ds/symlink/ds90lv047a.pdf?ts=1726209882189 It is low cost and LCSC currently shows some stock: https://www.lcsc.com/search?q=ds90lv047a It's even available on a handy (but expensive) break-out board. The board is intended for I2S over HDMI cable, but the pin-outs seem to match what we need (I had to look at multiple listings to even figure out what the connections are): https://www.ebay.com/itm/354879832003 Caution: The breakout boards seem to be available in both "Transmit" and "Receive" versions! Some of the sellers don't even seem to know what they are offering. I believe that the Transmit version is what I need for testing, but the listings are somewhat confusing. When I get it all sorted, I will likely order a board for some initial testing. Edit: Now I am seeing that this IC is designed for differential voltage output of only 300mV. Perhaps not as interesting as I thought. Edited 2024-09-14 03:55 by Sasquatch -Carl |
||||
stanleyella Guru Joined: 25/06/2022 Location: United KingdomPosts: 2120 |
very colourful and fast but how to make it circular? 'calculate centre and scale factor xc=MM.HRes\2-10:yc=MM.VRes\2 xs=MM.HRes\5:ys=MM.VRes\5 |
||||
Mixtel90 Guru Joined: 05/10/2019 Location: United KingdomPosts: 6779 |
I've just tried again, this time with 5V on the HDMI. My monitor goes into widescreen but synch isn't quite right. The image starts to jump after a few seconds. Do I need any other excuses to buy a new monitor? :) Mick Zilog Inside! nascom.info for Nascom & Gemini Preliminary MMBasic docs & my PCB designs |
||||
| Bleep Guru Joined: 09/01/2022 Location: United KingdomPosts: 509 |
Hi Mick, Did you see Carl's post I was going to give this a try tomorrow hopefully. Regards Kevin. |
||||
| Mixtel90 Guru Joined: 05/10/2019 Location: United KingdomPosts: 6779 |
Yep. As I've said though, I have no trouble using widescreen mode on a TV. There can't be much wrong with the signal. However, this monitor is a bit of an unknown when it comes to anything apart from bog standard HDMI modes. It might be that this is 50R and the TV is 60R - I dunno. I've no intention of messing up the PCB traces at this point anyway. No point as I've no control over whatever is already on the Pico 2. As a matter of interest, Alpha isn't using a breakout board. It's a normal HDMI socket. Mick Zilog Inside! nascom.info for Nascom & Gemini Preliminary MMBasic docs & my PCB designs |
||||
| stanleyella Guru Joined: 25/06/2022 Location: United KingdomPosts: 2120 |
no, go to currys and get ripped off there's tv with 1080 hdmi and an old one will have vga.scart,phono video yours should work with pico hdmi some way . what is it? is it a pc monitor? with hdmi or dvi? |
||||
| Mixtel90 Guru Joined: 05/10/2019 Location: United KingdomPosts: 6779 |
The TV is used as such upstairs. My monitor is in the living room downstairs. I'd swap them over but the TV is too big. The monitor is an AOC with two HDMIs and a VGA. It was an ebay buy just as my last one was dying and I was getting desperate. :) I have another monitor I can try but it's in a bit of an awkward position until my son moves out in a couple of weeks. I think that has DVI and VGA inputs IIRC. Mick Zilog Inside! nascom.info for Nascom & Gemini Preliminary MMBasic docs & my PCB designs |
||||
| stanleyella Guru Joined: 25/06/2022 Location: United KingdomPosts: 2120 |
only my olimex 2350 pico2 has hdmi but syncs fine on tvs with hdmi. never seen dvi on a tv, only hp pc monitors. never seen hdmi on pc monitor only vga. tried a different hdmi source to test the monitor? if it works then why pico hdmi not working? |
||||
| Page 4 of 4 |
|||||
 Print this page |
