Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 12:19 24 Nov 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Wanted : LG Rotor

Author Message
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 08:52pm 04 Nov 2009
Copy link to clipboard 
Print this post

I've a LG motor ,and I would like to get a second magnetic rotor .I'd like to fit it out with Neo's ..
If anyone out there would like to part with one of the "bigger" LG rotors,,(there are 2 types) ,,I'd be happy to buy..

Thanks
Bruce
Bushboy
 
grub
Senior Member

Joined: 27/11/2007
Location: Australia
Posts: 169
Posted: 08:03pm 06 Nov 2009
Copy link to clipboard 
Print this post

I have the magnetic rotor off a LG, the centre spline is chewed out and so it was replaced (can't buy the centre spline separately). What is the diameter of the rotor that you require and I will check the one that I have. If it is the same then you can have it as I will be only sending it off for scrap.
 
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 08:19pm 06 Nov 2009
Copy link to clipboard 
Print this post

Fhank You ,Mr. nice Grub ,lol.

The one I need is 300mm outside diameter by 70mm thick..

I could use the plastic "hub" bit from mine in yours once I fit it with Neo's.

(07) 55453513 and we will work out the mailing stuff..

Thanks
Bruce.
Bushboy
 
grub
Senior Member

Joined: 27/11/2007
Location: Australia
Posts: 169
Posted: 07:40am 09 Nov 2009
Copy link to clipboard 
Print this post

I reckon the one I have is the one you want. I left a message on your phone but if you can't understand me (I reckon I sound brain dead when I hear my recorded voice) then email me with your address and I will COD it to you via Aust. Post or the company of your account choice. Email is grubatausidotcom
Its all yours whenever you want it.
 
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 01:28am 10 Nov 2009
Copy link to clipboard 
Print this post

Thank You "Grub" ..
I'm "out of town " at present,,grandkids birthdays...

I'll e-mial the details to you asap...
Thank You for your kind reply,,,I hope it will benefit all that are interested at a later date..

Bruce
Bushboy
 
brett

Newbie

Joined: 08/02/2006
Location: Australia
Posts: 39
Posted: 12:13am 30 Nov 2009
Copy link to clipboard 
Print this post

Hi Bruce

Did you get the LG parts you need. I have a LG rotor and Motor (windings burnt) about the size you need.
Free if you want to pay postage and keep me informed on your progress with them.

Regards Brett
 
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 05:07am 30 Nov 2009
Copy link to clipboard 
Print this post

Thanks Brett,, Cameron(grub) has kindly sent me one and I hope my kind postie will keep it in the postoffice depot for when I arrive back later this week..

I do intend to retrofit with Neo's and could use yours also ..it has to be the larger motor-you know there are 2 ..one stator is around 30mm wide ,the smaller.. and the big one I am using is around 40mm ,a bit larger than the F&P all over..

So ,yes, I will take yours if it's the larger one .

Cameron put his in a padded bag and securely cross taped it with strong packing tape ,,did the trick ok.

Bruce Pickers
48 Macrozamia Dr.
Clagiraba
QLD 4211

Thank You for your interest..

Bruce
Bushboy
 
grub
Senior Member

Joined: 27/11/2007
Location: Australia
Posts: 169
Posted: 08:50pm 30 Nov 2009
Copy link to clipboard 
Print this post

Cameron? Who the hell is Cameron? Unfortunately, or fortunately, I am another Trevor :)
 
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 02:32am 01 Dec 2009
Copy link to clipboard 
Print this post



Ha,Ha ,,lol Mr. Grub ..

Just me ,an ol fa#t crackin up again.. Thought "Cameron" would be more polite than calling you "grub"...
Never mind ,

Bruce
Bushboy
 
grub
Senior Member

Joined: 27/11/2007
Location: Australia
Posts: 169
Posted: 08:47pm 01 Dec 2009
Copy link to clipboard 
Print this post

"Thought "Cameron" would be more polite than calling you "grub""
You haven't seen my backyard or workshop.
Was the rotor the correct one?
You should also get brett's burntout motor, can always rewire it.
 
brucedownunder2
Guru

Joined: 14/09/2005
Location: Australia
Posts: 1548
Posted: 08:16pm 05 Dec 2009
Copy link to clipboard 
Print this post

Thanks Grub ,, got your parcel yesterday ,,the rotor is corret one and was not damaged..

Brett, I'm home now ,,so call me on 07 55453513 if you want to chat about your motor..

Nice to have friends ,,
Thanks a lot guys

Bruce
Bushboy
 
VK4AYQ
Guru

Joined: 02/12/2009
Location: Australia
Posts: 2539
Posted: 01:20pm 20 Feb 2010
Copy link to clipboard 
Print this post

Hi Bruce

Hows the LG motor conversion going, I purchased one and would like to have a go at a twin unit if it would give a good output it is a lot more robust than a FP and I could double it up easier I think.
ALL the best

Bob
Foolin Around
 
KarlJ

Guru

Joined: 19/05/2008
Location: Australia
Posts: 1178
Posted: 03:35pm 03 Apr 2010
Copy link to clipboard 
Print this post

Bob, chat with Phillm on that one mate

he spent a shedload of time on it but to very little avail.
send him a pm
Luck favours the well prepared
 
VK4AYQ
Guru

Joined: 02/12/2009
Location: Australia
Posts: 2539
Posted: 01:02am 04 Apr 2010
Copy link to clipboard 
Print this post

Thanks Karl

Will do mate I got one on ebay and its muck like the f&p 80. but a bit bigger. I thought it would be a good project for when I get the fp up and going.
I thought Bruce had a bit of a play with them.

Will give Phillim a call to see what he found.

All the best

Bob
Foolin Around
 
leeyn
Newbie

Joined: 21/03/2011
Location:
Posts: 5
Posted: 06:41am 22 Mar 2011
Copy link to clipboard 
Print this post

What is the diameter of the rotor that you require and I will check the one that I have...
Buy RS GoldRunescape GoldRS Gold
 
VK4AYQ
Guru

Joined: 02/12/2009
Location: Australia
Posts: 2539
Posted: 02:20pm 22 Mar 2011
Copy link to clipboard 
Print this post

Hi leeyn

I will do a measure in the morning and get back to you, I think they are the same diameter though but one ahs a wider rotor and stator.

All the best

Bob
Foolin Around
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024