 Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me. |
Forum Index : Electronics : Power supply giveaway
| Author | Message | ||||
rotorhed Newbie  Joined: 29/01/2007 Location: AustraliaPosts: 36 |
Hi all I just wanted to let everyone know that I have 5 regulated power supplies with multiple output voltages for give away if anyone wants them just pay the freight and their yours. I know they were designed for powering electronics on buses so the input is 13.8v but can take up too 24v and the outputs are 11.2v, 5.2v and 5v the current rating as best as I can tell are 1amp for the 11.2v rail , 1amp for the5.2v rail and 2amps for the 5v rail Also I think it would be quite easy to change the voltage and current rating by changing some voltage regs on the board If anyone is interested let me know because their just going to the tip other wise ( a waste of good technology i know) Cheers Christian Marge the Winds are here Ah McCaine............. |
||||
| domwild Guru  Joined: 16/12/2005 Location: AustraliaPosts: 873 |
Christian, Thanks for the offer. Whereabouts in this big brown land are you? Taxation as a means of achieving prosperity is like a man standing inside a bucket trying to lift himself up. Winston Churchill |
||||
| rotorhed Newbie Joined: 29/01/2007 Location: AustraliaPosts: 36 |
Hi Dom I'm in Brisbane actually its close to to cleveland where I live and work. Cheers Christian Marge the Winds are here Ah McCaine............. |
||||
| domwild Guru Joined: 16/12/2005 Location: AustraliaPosts: 873 |
Thanks once again. Too far away for me, I'm in Perth! Regards, Taxation as a means of achieving prosperity is like a man standing inside a bucket trying to lift himself up. Winston Churchill |
||||
fillm Guru Joined: 10/02/2007 Location: AustraliaPosts: 730 |
Hi Christian , Im interested in these power supplies if it is not to late , I live near jimboomba not to far away from you ... Regards Phill.... PhillM ...Oz Wind Engineering..Wind Turbine Kits 500W - 5000W ~ F&P Dual Kits ~ GOE222Blades- Voltage Control Parts ------- Tower kits |
||||
| rotorhed Newbie Joined: 29/01/2007 Location: AustraliaPosts: 36 |
Hi Phill Yeah I still have them Let me know whether you want to pick them up or you want me to put them in a box and send them to you have not got a clue what freight would cost but probably a courier could do it pretty cheap because where both in the Brisbane area. Cheers Christian Marge the Winds are here Ah McCaine............. |
||||
South Easter Newbie Joined: 18/06/2007 Location: Posts: 36 |
Hi Christian, any of those left? If so, can you tell me dimensions and weight? South Easter http://windpower.org.za |
||||
| Robb Senior Member  Joined: 01/08/2007 Location: AustraliaPosts: 221 |
rotorhead I wouldn't post email addresses here 
The spam bots will be lurking  Try the edit function.
Unless you like emails about ere  ing things other than windmill towers that is. |
||||
| rotorhed Newbie Joined: 29/01/2007 Location: AustraliaPosts: 36 |
Hi south easter Sorry I turfed them out when I did a re arrange at my workshop about a week before you post. sorry for the delay Cheers Christian Marge the Winds are here Ah McCaine............. |
||||
 Print this page |
