Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 15:30 25 Nov 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Electronics : StarTrac 240v motor

Author Message
Madog

Newbie

Joined: 27/01/2009
Location: Australia
Posts: 25
Posted: 09:51pm 27 Jan 2009
Copy link to clipboard 
Print this post


G`Day all,

I actually have a StarTrac motor from a commercial treadmill, I am wanting to eventually set up for a home built Hydro Vortex generator, from what I have seen it will need to be run through a geared belt drive mechanism.

This motor puts out 18 Vdc when I spun the weighted flywheel by hand.
Anyone have an idea what it would put out by looking at the label ?

Regards,
Den

Small minds discuss people, Average minds discuss events, Great minds discuss ideas, Be GREAT !

See this Great engine with No Crankshaft: http://www.revetec.com
 
GWatPE

Senior Member

Joined: 01/09/2006
Location: Australia
Posts: 2127
Posted: 02:05am 28 Jan 2009
Copy link to clipboard 
Print this post

Hi Madog,

The wire is rated for continuous 8.75A. The output volts from the nameplate indicate about 24V for 350rpm.

As a hydro probably 1000-1500 rpm tops, so take the 8.75A @ say 100V, so <1000W.

The 2.5hp is at 3500rpm, divide this by about 3, so this gives about 700W.

Gordon.Edited by GWatPE 2009-01-29
become more energy aware
 
Madog

Newbie

Joined: 27/01/2009
Location: Australia
Posts: 25
Posted: 01:23am 17 Mar 2011
Copy link to clipboard 
Print this post

  GWatPE said   Hi Madog,

The wire is rated for continuous 8.75A. The output volts from the nameplate indicate about 24V for 350rpm.

As a hydro probably 1000-1500 rpm tops, so take the 8.75A @ say 100V, so <1000W.

The 2.5hp is at 3500rpm, divide this by about 3, so this gives about 700W.

Gordon.


I have not been back here for a long time, good to see all is active !

I noted it actually says 240volt and 8.75A @ 3'500rpm, not sure if that equates to 24v @350rpm.
This project is still on the back burner.
If any one has any futher info please post.

Regards,
Den
Small minds discuss people, Average minds discuss events, Great minds discuss ideas, Be GREAT !

See this Great engine with No Crankshaft: http://www.revetec.com
 
Alasdair
Regular Member

Joined: 12/01/2011
Location: Australia
Posts: 62
Posted: 08:45am 18 Mar 2011
Copy link to clipboard 
Print this post

That motor is 2kw, because it is rated for
variable speed it can run slower without
cooling loss, but efficiency losses will not
make it a linear power to voltage exponent
and as a generator it will be different again
as the winding impedance will have a greater
effect at lower voltage. Best trick is to drive
it with something like a small petrol motor or
a lathe to plot it's output over a wide speed
range. It is a brush commutator so it's life
will be a bit limited, but still good potential.
Amc-elec
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024