Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Solar : 12V Solar charger MPPT for 18650 (2s, 4p) with 3.3V and 5V output
I am replacing my current weather station with something smaller. The brain of the weather station is going to be an ESP32 as I want to use the WiFi capabilities. The project will be charged by a 10W, 12V solar panel. I live in Melbourne and we can have many days of overcast conditions, so, I'll need redundancy in battery capacity. I did the sums and I probably need 4x 18650 Li-ion cells in parallel. But because I also need a stable 5V output for my sensors I probably need to double the batteries so that I can put them in series to achieve 8.4V (If that makes sense). I will also need protection against over- and under-voltage. Anyway, I did my research and I think the following is going to be my best option:
The 12V solar panel will be connected to a CN3795 MPPT Li-ion charge control module. I will put a Schottky diode to prevent drainage overnight. I then will connect two Mini360 switching power regulators. One will be set to 3.3V and the other to 5V with common ground
I am not an electronics specialist and I would like to receive some constructive feedback if my thinking process is in the right direction. I've been looking for off-the-shelf MPPT chargers but I can't find anything for multiple 18650 cells in parallel. Most chargers are for lead-acid battery technology but I want to switch to Li-ion batteries as they are common, cheap and long-lasting (When treated correctly).
Also, I've been told that it's possible to buy 18650 Li-ion batteries with inbuilt BMS; Is that correct? If yes, where do I find these? I don't want to skimp on quality and reliability so brands like Samsung or Panasonic would be the best.
Anyway, I hope somebody can give me a nudge in the right direction. Many thanks in advance for your help/advice! Cheers,
Luke
Revlac Guru Joined: 31/12/2016 Location: AustraliaPosts: 1020
Posted: 08:46am 22 Sep 2023
Copy link to clipboard
Print this post
Hi Luke, Welcome to the Forum.
You can parallel 2 or more 18650 cells, you still only need to balance it as one cell, Actually all it needs in over and under voltage protection.
If you want 2 in series, there is 2S balances available, 2S2P should be fine. I don't know of any 18650's with built in BMS, its unlikely it would fit in the 65mm size constraint. The CN3795 is a neat little unit. I'm not an Expert either. Cheers Aaron Off The Grid
Thanks Aaron. Yes, I was also surprised to hear about 18650 with inbuild BMS. I've never seen anything like it either. It looks like that I will look at building a BMS for each 2S2P battery set. Good to see your endorsement for the CN3795. I will give it a try. Thanks for your response! Much appreciated! Luke
pd-- Senior Member Joined: 11/12/2020 Location: AustraliaPosts: 122
Posted: 05:13am 24 Sep 2023
Copy link to clipboard
Print this post
You can get protected cells that have a over/under voltage cutout built into the cell. https://www.aubattery.com.au/product/panasonic-18650b-3400mah-protected-li-ion-battery/
in the base of the cell is a pcb with a monitoring IC and fet's it will disconnect the cell if under or over voltage
There designed for applications that have no builtin smarts ie torch.
Revlac Guru Joined: 31/12/2016 Location: AustraliaPosts: 1020
Posted: 05:18am 24 Sep 2023
Copy link to clipboard
Print this post
First I have seen, how well will it work in series?Cheers Aaron Off The Grid
Hi pd, That's a great recommendation! And the price is not bad either. Thanks for the link and info!
pd-- Senior Member Joined: 11/12/2020 Location: AustraliaPosts: 122
Posted: 05:56am 24 Sep 2023
Copy link to clipboard
Print this post
I have one torch that takes 2 in series. it just turns off when one cell goes lo voltage and its the cell that is turning off as the torch just gets dimmer & dimmer with other cells
I have 6 cells that i have been using in dumb devices for ~3 years now they just work.
Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Print this post
